Debian suspend not working. when i login then, it asks for the root password.

Debian suspend not working Nov 26, 2023 · running debian trixie with xfce, i am facing some problems with suspend. running debian trixie with xfce, i am facing some problems with suspend. As launched without desktop connected, suspension does not work. In this case, I have to hold the power button for a while to start my laptop. . when i leave my workstation, it turns off the screens after about 10 minutes and then should go to suspend. conf and change the lid switch settings, as well as /etc/systemd/sleep. Earlier with Debian-10 on same desktop, on pressing Suspend, the screen would go blank, the disk activity would stop and the power light would go from continuous on to slow blinking state. The following solutions were reported to get the touchpad working again: Switch to a console, then switch back to X again ; or Hi, I have a system with an unencrypted \boot partition and encrypted \root. My experience was that after every suspend or hibernate when I would try to resume I would encounter garbage on GUI screen so could not successfully resume. Oct 14, 2023 · I just passed on Debian 12 from Win10. How can I tell gnome-power-manager to use s2ram and s2disk instead of whatever it is trying to use? Or, if the former is not possible, how do I get the default Debian suspend and hibernate methods to work? My hardware is listed below in my signature. Jun 16, 2023 · Yes, suspend works without any problem, from the menu, from commandsit works perfectly. Suspend not working on Debian 11. Trying from the shutdown menu in Gnome, or by using systemctl suspend, I… Aug 7, 2019 · Re: Suspend not working on Debian 11 Post by FreewheelinFrank » 2022-10-22 06:19 A very common issue found after the computer resumes is corrupted video (or black screen, or no LCD backlight). target DOES NOT pre running debian trixie with xfce, i am facing some problems with suspend. target hybrid-sleep. After that, when I try on terminal Jul 13, 2023 · You can try unloading and reloading the ath9k driver manually after the resume from suspend--as root or with sudo: rmmod ath9k modprobe ath9k If that works, there is a file on the system that you can add that driver too which will remove it before suspend and reload it afterwards, but I am on my phone right now so can't recall that off hand. Aug 15, 2021 · I have/had the same issue after new install (not upgrade) of Debian 11 on my Dell Optiplex 780 just yesterday. This is not the same as suspend. sh for good measure with no change. Jul 28, 2023 · After installing Debian 12 on my laptop, suspend sometimes doesn't work. sudo systemctl mask sleep. I've read these two official documentations on the matter: Suspend and hibernate configuration in Debian Jessie; SystemdSuspendSedation; I've tried to make this simple script to see if anything is working: When I suspend my laptop with 15% of the battery energy and try to resume, it doesn't work. The output of the command is obviously fuller than the settings you reported. Sometimes when resuming from hibernate/suspend mode, the touchpad may stop working, even if synclient reports it as activated. What is the problem? My system is Debian 8. As I am not a Cinnamon user, I could not test if that command would work. I did not have the issue with latest updated Debian 10 on same machine. Dec 19, 2023 · I have tried to go into /etc/systemd/logind. Suspend means (at least to me) to write the contents of RAM to disk and put the system to sleep. I tried using cryptsetup-suspend but it doesn't work. conf to manually activate suspend by allowing with YES. Touchpad does not work after resuming from hibernate/suspend. As it did, you do not need to use it (although it may be useful for editing settings). I can't figure out the reason, and the further I've reached is to this dmesg output: After installing Debian 12 on my laptop, suspend sometimes doesn't work. debian. target suspend. Post by pedronovaes » 2022-10-21 17:35. See full list on wiki. I have to hold the Sep 6, 2022 · Before going further, you should have a look to "Sleep State" BIOS/UEFI configuration:-> [Linux S3]: Optimized Sleep State for versions of Linux that are not compatible with Suspend-to-Idle running debian trixie with xfce, i am facing some problems with suspend. The laptop is not able to suspend, while in Win10 suspension and hibernation worked with no problem. Hi guys, when I suspend my laptop and try to resume, it doesn't work. Feb 8, 2024 · Similar to the suspend feature, hibernation allows you to save your system’s work by transferring the contents from RAM to the swap file on the hard disk. Suspend does not work. org Feb 17, 2022 · However, the "Suspend" is not working properly. Upgrade from 11. Unfortunately, nothing seems to be working. target hibernate. 0. This process involves completely Dec 9, 2020 · Perhaps we are not using suspend in the same context. Trying from the shutdown menu in Gnome, or by using systemctl suspend , I encounter the same random behavior. It has not ran out of charge; as I have left it on charge when it was in suspend and also suspended for short periods of time on a full charge. Oct 18, 2021 · The main issue is that when I put my computer into suspend mode, there's about a 40% chance that when I go to wake it up from suspend, the computer turns on but the screen remains black. Nov 27, 2023 · running debian trixie with xfce, i am facing some problems with suspend. when i come back to my workstation, it seems like as if i was logged out but all is up and running. Jul 6, 2021 · HandlePowerKey=suspend with a desktop monitor plugged in the computer suspends on pressing the power button. I tried setting /usr/sbin/pm-suspend in powerbtn-acpi-support. Jul 12, 2015 · Today I observed that suspend sometimes does not work properly in freshly installed Debian Jessie. I have no idea what could cause that. After executing suspend (Alt + Shut Down button) the following message appears on black screen: Loading, please wait Dec 3, 2023 · I already asked in #debian-next and on the forum, but thought I'll also ask here before switching back to Fedora. After installing cryptsetup-suspend, when I try to suspend I get a black screen with the following text and a blinking cursor: Apr 15, 2006 · After installing uswsusp, I can suspend my laptop with s2ram -f and I can hibernate with s2disk. Jun 13, 2023 · Just installed Debian 12. If you have power connected full time, then it's simpler to just put the display to sleep and keep the system running. Feb 11, 2024 · dconf-editor is just an alternative way of getting the same information. when i login then, it asks for the root password. When I use systemctl suspend, the workstation goes into suspend for about 1 second and then comes back. 2 didn't work, so installed clean from Bookworm DVD. tjj amebr gxtb bmscjnj cwjqis ipmeti axlqbf fjfopo sxz quox